Toughness and R-curve behaviour of laminated Si3N4/SiCw ceramics

Laminated Si₃N₄/SiC_w ceramics were successfully prepared by tape casting and hot-pressing. Its mechanical properties were measured and the impact resistance was discussed. The toughness of the laminated Si₃N₄/SiC_w ceramics was 13.5 MPa m^1/2, which was almost 1.6 times that of Si₃N₄/SiC_w composite ceramics, namely 8.5 MPa m^1/2. Moreover, the indentation strength of laminated Si₃N₄/SiC_w ceramics was not sensitive to increasing indentation loads and exhibited a rising R-curve behaviour, indicating that the laminated Si₃N₄/SiC_w ceramics had excellent impact resistance. The improved toughness and impact resistance of laminated Si₃N₄/SiC_w ceramics was attributed to the residual stress caused by a thermal expansion coefficient mismatch between the different layers, resulting in crack deflection and bridging of SiC whiskers in the interface layer, thus consuming a large amount of fracture work.     

分光光度法测定PVB中微量氯含量

建立了PVB树脂中氯含量的测定方法.采用添加混合试剂高温灰化,沸水浸取,分光光度法测定PVB树脂样品中的氯含量.该方法具有良好的精密度和准确度,分析成本低.     

Synthesis of nanopowders with low agglomeration by elaborating Φ values for producing Gd2O3-MgO nanocomposites with extremely fine grain sizes and high mid-infrared transparency

Refining ceramic microstructures to the nanometric range to minimize light scattering provides an interesting methodology for developing novel optical ceramic materials. In this work, we reported the fabrication and properties of a new nanocomposite optical ceramic of Gd₂O₃-MgO. The citric acid sol-gel combustion method was adopted to fabricate Gd₂O₃-MgO nanocomposites with fine-grain sizes, dense microstructures and homogeneous phase domains. Nanopowders with low agglomeration and improved sinterability can be obtained by elaborating Φ values. Further refining of the microstructure of the nanocomposites was achieved by elaborating the hot-pressing conditions. The sample sintered at 65 MPa and 1300 °C showed a quite high hardness value of 14.3 ± 0.2 GPa, a high transmittance of 80.3 %–84.7 % over the 3?6 μm wavelength range, due mainly to its extremely fine-grain size of Gd₂O₃ and MgO (93 and 78 nm, respectively) and high density.     

Brönsted方程动力学模型研究ZSM-5催化乙烯齐聚及芳构化活性和酸强度分布之间的定量关系

乙烯催化齐聚和芳构化是烯烃高值化和合成液体燃料的关键过程，采用NH₃-TPD谱图分析计算方法得到的探针分子脱附活化能作为催化剂的酸位点强度分布的参数，结合线性自由能理论在Br?nsted方程中引入酸强度对反应的影响因子γ作为动力学方程参数关联探针分子脱附活化能与反应活化能，明确固体酸酸强度的基准在催化动力学方程中的物理意义。建立同为MFI拓扑结构 Si /Al摩尔比为12.5、19、25、60、70的ZSM-5分子筛催化剂上不同酸强度位和乙烯齐聚及芳构化中氢转移、齐聚、芳构化各单元步骤以及对应的烷烃、低碳烯烃和芳烃产物分布的定量关系。根据拟合得到动力学参数γ可以发现不同强度的酸位点对乙烯齐聚及芳构化具有不同的作用系数。氨脱附活化能(DAE)为90 kJ·mol^-1的酸位点是氢转移反应的主要活性位点，而对于乙烯齐聚反应中主要的活性酸位点为DAE 90 kJ·mol^-1和124 kJ·mol^-1，DAE为150 kJ·mol^-1的酸位点是芳构化反应的主要活性位点。     

45 t门座起重机顶升方案设计

针对国内45 t门座起重机大车行走机构平衡梁裂缝问题。分析平衡梁裂缝产生原因并提出相应的维修方案,并对维修关键技术中的顶升方案设计,采用Ansys软件对其强度进行了有限元分析,同时对维修前后的平衡梁进行分析并对比。将维修方案应用于实际工程,取得了较好效果。该顶升机构修复方案设计符合工程实际,对工程实践具有一定的指导意义。     

脱硫胶粉在乳化改性沥青中的应用

考察了不同规格胶粉及不同脱硫程度的脱硫胶粉对橡胶改性乳化沥青性能的影响,结果表明,采用100目胶粉即可制备出橡胶改性乳化沥青,但乳化沥青的性能较差;采用活化度为50%左右的100目脱硫胶粉制备乳化沥青时,脱硫胶粉的用量相比于胶粉可大幅提高;在通过外掺100目50%左右活化度的脱硫胶粉(质量分数15%,以沥青计,下同)和质量分数2%的苯乙烯-丁二烯-苯乙烯嵌段共聚物改性的乳化沥青中添加质量分数1%的丁苯胶乳,所制备橡胶改性乳化沥青无筛上剩余物,5 d储存稳定性为2.9%,蒸发残留物的25℃针入度、软化点和5℃延度分别为55 (0.1 mm)、64.5℃和22.5 cm,能够满足乳化改性沥青的技术指标要求。     

中国智能机械制造评价及发展研究

以中国规模以上工业企业数据库为基础，结合在智能制造主要区域调研的结果，筛选出15145家智能制造企业，经同行评议后，生成322家候选企业名单；再由资深产业专家从“开发式创新”和“探索式创新”两个方面去考察候选企业的能力，得到中国智能制造百强排行榜；随后根据行业分类，得到智能机械制造企业排行榜。在概述了智能机械制造上榜企业的基本情况后，着重分析了前20强企业，并提出了中国智能机械制造发展路径和未来的发展趋势。